Home › Forum › Ask A Member › Getting the gas out when you’re done using a motor.
- This topic has 23 replies, 11 voices, and was last updated 2 years, 3 months ago by joecb.
-
AuthorPosts
-
May 28, 2022 at 11:11 am #260563
I can count on one hand the motors I have
gotten that didn’t have old, often dried up
gas, left in them.
.
I always run a motor till it quits when I’m
done running them but there is almost always
some gas left in the tank. Trying any number
of ways to get the rest out was always a pain.
.
Now I have a dumpster full of great ideas that
didn’t work out. This device was on its way to
the trash after another failure when I need to
get the gas out of this motor to travel.
I wonder?
.
You do needed a pretty stiff bottle to pull the
gas up. The one I’m using is barely stiff
enough so I’m having to help it some.
.
This wasn’t my intent for this “Boat House”
device. Timing had a lot to do with it.
Tubs.May 28, 2022 at 11:33 am #260566If you make the hose a little longer and put the bottle below the tank it will siphon till empty. I use a similar set-up with a gas line and squeeze bulb.
May 28, 2022 at 11:58 am #260567If you make the hose a little longer and put the bottle below the tank it will siphon till empty. I use a similar set-up with a gas line and squeeze bulb.
That sould work if once I got the gas flowing I pulled the hose out of the bottle.
Tubs.May 28, 2022 at 12:04 pm #260568sucking it out with a small vacum pump or your mouth via a small 2 “hosed” holding jar…… should take it all out
some brake line vacum pumps used for GC pressure and VACUM testing can suck it out and you won’t need to brush your teeth after 🙂
Joining AOMCI has priviledges 🙂
- This reply was modified 2 years, 3 months ago by crosbyman.
May 28, 2022 at 1:53 pm #260572Gearcase lube pump.
If you have too many, AND not enough, you're a collector.
May 28, 2022 at 7:54 pm #260581I use an OMC primer bulb in the middle of a 4′ length of fuel hose. I have about a foot of 3/8″ copper tubing jammed into the inlet end which lets me get to the far reaches of tanks as necessary. Use copper, NOT anything that might spark. Just drop the copper tubing end into a tank of gas, the other end in your portable tank, and squeeze the primer bulb.
Tom
May 28, 2022 at 8:24 pm #260586after gold… copper is probabaly the second best electricity conductor…it may not cause a sprak from friction but… it will carry your static electricity quite well 🙂
just a rubber hose should do fine.. anything left is a dark corner will evaporate …or dump a rag in the tank to soak it up then pull it out with a stiff hooked wire
Joining AOMCI has priviledges 🙂
- This reply was modified 2 years, 3 months ago by crosbyman.
May 28, 2022 at 9:16 pm #260588I use an OMC primer bulb in the middle of a 4′ length of fuel hose. I have about a foot of 3/8″ copper tubing jammed into the inlet end which lets me get to the far reaches of tanks as necessary. Use copper, NOT anything that might spark. Just drop the copper tubing end into a tank of gas, the other end in your portable tank, and squeeze the primer bulb.
Tom
I was use the same setup to get the fuel out of my pressure tank. Take a little bit of squeezing but it works great
MARK-7, KF-7, KE4-A, MARK 15, WN7A, (60)MERC 200
May 29, 2022 at 11:01 am #260608Squeeze bottle, simple and with a small diameter tube to get the “good to the last drop” out… I like it.
Many carbs have a drain screw on the bowl, look for it… get the last drops out of the carb.
Joe B
May 29, 2022 at 7:37 pm #260628Forgive me for hijacking this post, but what to do about the gas remaining in the carburetor on those carburetors that do not have drain plugs? I’m told it is a bad idea to run the engine dry because there is no lubricating oil present when the gas runs out, but the engine is still sputtering with what little gas remains. I’m not sure i believe that, but there is some logic to it. Then there is the problem of running the gas out of one carburetor until the engine quits, but still having gas in the other carburetor(s). The alternative it to disassemble the carburetors to remove the remaining gas which will usually be at the end of the season when it is nice and cold out and one isn’t real excited about tearing the carburetors apart anyhow. Any thoughts?
-
AuthorPosts
- You must be logged in to reply to this topic.