Home Forum Ask A Member 1953-54 25 horse evinrude

Viewing 10 posts - 11 through 20 (of 22 total)
  • Author
    Posts
  • #284985
    crosbyman
    Participant

      Canada Member - 2 Years

      I tried… and tons of utubes out there !

      https://youtu.be/r7A6d8me0Gw

      https://youtu.be/ZAlT32NnTJ0

       

       

       

      Joining AOMCI has priviledges 🙂

      #285019

      Took advice from both of you guys, then watched a couple of youtubes, doing exactly as you and the videos showed. Ordered new coils just now.

      #285020
      crosbyman
      Participant

        Canada Member - 2 Years

        jfyi….for some reason  coil HV secondary windings  seem to be  increasing  in the higher ohm  range these days.    Amazon stuff anyway.

        Most of my recent ones  were around 8kohms +  whereas  older one were  lower in the  4-7 kohms   range.

        Can’t say they don’t work but I always preferred the lower range ones because  I have  this suspicion  the new ones  have  smaller  gauge  wire causing  resistance  to increase but worse…. such fine  wire is surely more delicate and could lead to insulation failure   on the varnish.      Time will tell I guess.

        Smaller wire on the secondary allows  cost cutting especially if they kept the same amount of turns.  Magnetism is a strange thing … current   #of turns.. ratios  etc…

         

        Unfortunately the only way to know   would be  a lobotomy/autopsy     or   accurate electrical testing  HV voltage outputs  to compare   low and  high end  secondaries performance

         

         

        Joining AOMCI has priviledges 🙂

        #285021

        One other thing, recommended spark plugs for this engine?
        <!–more–>

        #285024
        crosbyman
        Participant

          Canada Member - 2 Years

          book  says  Champion J6-J    if available  or modern eqv.

          Joining AOMCI has priviledges 🙂

          #285025
          crosbyman
          Participant

            Canada Member - 2 Years

            to service oldies you should get the bible…. just download  for 20$  400+ pages   on all you need to know

            what year did champion discontinue J6J spark plug | Antique Outboard Motor Club,Inc (aomci.org)

             

            https://watercraftmanuals.com/outboard/johnson/manuals/johnson-302231.htm

             

            Joining AOMCI has priviledges 🙂

            #285060

            I have downloaded it. Evinrude is not the same as Johnson although there is alot of crossover , somethings look different in the illustrations.

            #285064
            crosbyman
            Participant

              Canada Member - 2 Years

              agree there may be small difference ex: cowls   but they are cousins of the same father  🙂

              Unless you plan to crack one open for piston crankcase work  I think you will find all you need to know.  I printed mine double sided and spring bound with plastic cover sheets .

              Joining AOMCI has priviledges 🙂

              1 user thanked author for this post.
              #285071

              Both coils arrived, one has a 5500 ohm reading, the other is 13,500

              #285078
              crosbyman
              Participant

                Canada Member - 2 Years

                135000 sounds suspect…for reasons explained

                in theory  more resistance = longer thinner (if they matched turns) to theoretically generate  a high voltage (GREAT !) .

                Unfortunately  that may increase the potential  of  punching the insulating varnish of smaller than a hair wires  ( again…..if they matched the  turn count )  and that  is no fun  miles out on the water 🙁

                jmho

                Joining AOMCI has priviledges 🙂

              Viewing 10 posts - 11 through 20 (of 22 total)
              • You must be logged in to reply to this topic.